Advertise on the GDN Network
 
 
 
 
GDN Home
News Archives
Members List
Submit Article
GDN Newsletter
GDN Media Kit
Interviews
Reviews
Previews
Screenshots
GDN TV
Patches/Updates
Upcoming Releases
Publishers/Developers
Games List
Review Score Scale
Christophor Rick
The Art of the Press Re...
The Art of the Game Pre...
Shane Dickson
Off to a Good Start...




Chu`s Dynasty
Break Limit
Crimecraft Bleedout Official
TRON Evolution - Multiplayer
TRON Evolution - Wii
Marvel Pinball Launch
Fight Night Champion - Bishop
NBA Jam - Dwight Howard
Battlefield Heroes Christmas Heroes
DICE Community Mgr Interview - Battlefield Bad ...


GDN Proudly Hosted
on an HWS VPS

Index Blogs
Triangle Mesh Voxelization

Posted by DEVWolfire, Dec 31, 1969 19:00

In my recent post on automatic skinning, one of the steps involved creating a voxel representation of the character. I couldn't find any explanations of how to do this on the Internet, so I decided to write my own!

What is a voxel?

"Voxel" is short for "volume pixel". A pixel is a single square in a 2D image, and a voxel is a single cube in a 3D lattice. Voxel models are useful in games because they aren't hollow like triangle meshes are, so we can use them for 'deep' physical simulations such as heat diffusion, fracture, and soft physics. I used voxels extensively when working with Alec Rivers to visualize his RealMatter technology, and when testing out destructible cover for an unreleashed shooter project.

Here is the example model that I used for the previous post again -- the triangle surface is on the left, and the voxel model is on the right.


So how do we make a voxel model?

A voxel model is a bounded 3D grid, so the first step is to decide its basic characteristics. How big is each block, and what are the dimensions of the grid?

The size of each block depends on what you need it for -- in this case we are using it for attaching the mesh to the bones, so we only need enough resolution to make sure that important details like the mouth and fingers are not lost. Let's say each block is 1 cubic cm in size.

The dimensions of the grid have to be big enough to fit the entire model, but no bigger (to avoid inefficiency). This is fairly simple -- we can just set the dimensions equal to the size of the bounding box of the surface triangles (the smallest box that encloses every point) rounded up to the nearest centimeter. Here's a picture of the voxel grid:

Now we have to decide which voxels are solid (intersecting the model), and which voxels are not. The method I used is a two-step process. First, we solidify a shell representing the surface, and second, we fill it in using a scanline fill algorithm. This is most clearly illustrated by looking at a single slice -- first we have just the triangle surface, next the voxel shell, and finally the filled voxel model.

Calculating the shell is pretty straightforward. For every triangle, I check every voxel in the triangle's bounding box to see if it intersects. If it does, the voxel is made solid.

Filling the shell is a little more complicated. We can see this best by looking at a single row as it's filled in. You can think of a pen scanning from left to right that goes down to the paper when it hits an outside edge and raises again when it hits an inside edge. We start out on the left with the pen up, shown here as a green square.

There is no surface here and the pen is up, so we just move onto the next square without changing anything.

Here there are some intersecting surface triangles! We send a horizontal ray from left to right through the center of the voxel to see what it intersects. If the last triangle it intersects is facing to the left, then we lower the pen. Otherwise, we keep it raised.

Here is a close-up of this voxel. The small white lines represent the triangle normals (which way is 'out').

The last (and only) triangle that the pen intersects faces to the left, so we lower the pen! Here we illustrate that by changing the pen from green to red.

Since the pen is down, it fills in empty voxels as it steps to the right.

This process continues until we get to the next intersection. Fill, step to the right. Fill, step to the right.

Here's a close-up of this intersection test. The rule is the same as before: If the last triangle the pen intersects is facing to the left, then we keep the pen lowered, otherwise, we raise it up.

In this case the last (and again, only) triangle is facing to the right, so we raise the pen.

As it keeps moving out of the model, the pen is raised, so it fills no voxels. When we repeat this process for every row, the whole slice is filled in!

Here is a 3D view of half of the model: first, a surface slice, next, the voxel shell, and finally, the filled voxel model.

That's all there is to it! I hope this helps you use voxel models in your own projects. Do you have any ideas about better ways to voxellize triangle meshes, or any questions about how this works?

Follow us here!
Facebook icon ModDB icon Steam icon Twitter icon YouTube icon

Comments
Rules
1. No cursing or swear words: Use proper language to express yourself.
2. No flooding or spamming the comment system, abuse will result in a ban.

 
 
Search the site:

  Follow GDN at:

EVE Online Incursion | Fri, 03 Dec 2010
Description: Notice: Monthly subscription fee required after first month. Product keys w...[more]
Dawn of Discovery Gold Edition | Fri, 03 Dec 2010

Dawn of Discovery Venice | Fri, 03 Dec 2010

Ironclads Anthology | Fri, 03 Dec 2010

Detective Agency Mac | Fri, 03 Dec 2010

Once Upon a Time in Chicago Mac | Fri, 03 Dec 2010

Kivis Underworld Mac | Fri, 03 Dec 2010

Depths of Peril | Fri, 03 Dec 2010

Dreamscape | Fri, 03 Dec 2010

X-Tension | Fri, 03 Dec 2010


Affiliations
& Friends




Italian Videogame Developers Conference

 
Advertise | Submit News | Contact | Pages | Blogs | Downloads | Video | Privacy Policy | About Us | GDN Staff | GDN Review Scale
News & Articles RSS | News RSS | Article RSS | Video RSS | Reviews RSS
 
 
|